상품명 | [Adafruit-A385] DHT22 temperature-humidity sensor + extras |
---|---|
판매가 | 25,000원 |
제조사 | Adafruit |
원산지 | 해외 |
적립금 | 250원 (1%) |
상품코드 | P000BADL |
배송방법 | 택배 |
배송비 | 3,500원 (150,000원 이상 구매 시 무료) |
수량 |
SNS 상품홍보 | |
---|
(최소주문수량 1개 이상 / 최대주문수량 0개 이하)
사이즈 가이드수량을 선택해주세요.
위 옵션선택 박스를 선택하시면 아래에 상품이 추가됩니다.
상품명 | 상품수 | 가격 |
---|---|---|
[Adafruit-A385] DHT22 temperature-humidity sensor + extras | 25000 ( 250) | |
총 상품금액(수량) : 0 (0개) |
*Adafruit 제품은 해외배송 입니다
배송기간 이 약 2주 소요 됩니다
해외배송 제품은 주문 후 취소가 불가능 합니다
교환,반품,기술지원 이 불가능 합니다
구매전 이점 꼭 확인해 주세요*
The DHT22 is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air, and spits out a digital signal on the data pin (no analog input pins needed). Its fairly simple to use, but requires careful timing to grab data. The only real downside of this sensor is you can only get new data from it once every 2 seconds, so when using our library, sensor readings can be up to 2 seconds old.
Simply connect the first pin on the left to 3-5V power, the second pin to your data input pin and the right most pin to ground. Although it uses a single-wire to send data it is not Dallas One Wire compatible! If you want multiple sensors, each one must have its own data pin! We have written an Arduino library with example code
Compared to the DHT11, this sensor is more precise, more accurate and works in a bigger range of temperature/humidity, but its larger and more expensive
Comes with a 4.7K - 10K resistor, which you will want to use as a pullup from the data pin to VCC.
Downloads:
상품의 사용후기를 적어주세요.
게시물이 없습니다
상품에 대해 궁금한 점을 해결해 드립니다.
게시물이 없습니다
고액결제의 경우 안전을 위해 카드사에서 확인전화를 드릴 수도 있습니다. 확인과정에서 도난 카드의 사용이나 타인 명의의 주문등
정상적인 주문이 아니라고 판단될 경우 임의로 주문을 보류 또는 취소할 수 있습니다.
무통장 입금은 상품 구매 대금은 PC뱅킹, 인터넷뱅킹, 텔레뱅킹 혹은 가까운 은행에서 직접 입금하시면 됩니다.
주문시 입력한 입금자명과 실제입금자의 성명이 반드시 일치하여야 하며, 7일 이내로 입금을 하셔야 하며 입금되지
않은 주문은 자동취소 됩니다.